642-359 Implementing Cisco Storage Network Solutions

Page 1   
Question 1

Which of the following tools would you use to view SCSI error count statistics?

  • A. Cisco Performance Manager
  • B. RMON
  • C. Cisco Traffic Analyzer
  • D. Cisco Fabric Analyzer


Answer : C

Question 2

Which three of these statements are attributes of the Cisco SET? (Choose three.)

  • A. SET configuration is persistent.
  • B. Only SCSI read/write commands are supported.
  • C. SET initiators can only communicate with SET targets.
  • D. SET requires SAN-OS 2.0 or higher and the SAN Extension IP license.


Answer : B,C,D

Question 3

Which feature detects hardware faults and attempts recovery actions?

  • A. Switch Health Analysis
  • B. Fabric Configuration Analysis
  • C. Online Health Management System
  • D. End-to-End Connectivity Analysis
  • E. Cisco Fabric Services


Answer : C

Question 4

Your company has a multiswitch fabric including Switch A and Switch B. An administrator
of Switch A creates the following zone set and successfully activates it:
zoneset name ZoneSetl vsan 1
zone name Zonel vsan 1
pwwn 21:01:00:e0:8b:3c:03:b6
pwwn 21:01:00:e0:8b:3c:55:bb
Later in the day, a second administrator creates the following zone set on Switch B:
zoneset name ZoneSet2 vsan 1 zone name Zonel vsan 1 pwwn 21:01:00:e0:8b:3c:03:b6
pwwn 21:01:00:e0:8b:3c:55:aa
What happens when the administrator of Switch B attempts to activate ZoneSet2?

  • A. ZoneSet2 becomes the active zone set for both Switches A and B.
  • B. The fabric segments and ZoneSet2 become the active zone set for Switch B only.
  • C. The fabric segments and ZoneSet2 become the active zone set for Switch A only.
  • D. The fabric segments and ZoneSetl remain the active zone set for Switch B, while ZoneSet2 becomes the active zone set for Switch A.


Answer : A

Question 5

Which three of these terms are valid Fibre Channel topologies? (Choose three.)

  • A. point-to-point
  • B. switched backbone
  • C. Gigabit Ethernet
  • D. arbitrated loop
  • E. switched fabric
  • F. autonomous region


Answer : A,D,E

Question 6

Which configuration will enable remote access management using Telnet?

  • A. interface mgmt0 ip address 10.0.0.1 255.255.255.0 remote-access enable
  • B. interface mgmt0 ip address 10.0.0.1 255.255.255.0 feature telnet enable
  • C. interface mgmt0 ip address 10.0.0.1 255.255.255.0 telnet enable
  • D. interface mgmt0 ip address 10.0.0.1 255.255.255.0 telnet server enable


Answer : D

Question 7

Which license is required on switches that are going to implement LUN zoning?

  • A. Storage Services Enabler
  • B. Enterprise license
  • C. Fabric Manager Server license
  • D. SAN Extension over IP license


Answer : B

Question 8

When configuring FCIP, packet fragmentation should be avoided in order to achieve
optimal throughput. Fragmentation can be avoided by knowing which of the following?

  • A. MTU of the source IP interface
  • B. largest MTU in the path
  • C. smallest MTU in the path
  • D. MTU of the destination IP interface


Answer : C

Question 9

Refer to the exhibit.


You have deployed this access control list to prevent clients in IP subnet 10.1.1.0/24 from
accessing the Cisco MDS Switch through the mgmt0 interface using the configuration
shown in the exhibit. When you try to access the Cisco MDS Switch from your
management workstation, which has an IP address of 10.255.255.1, you discover that the
Telnet session cannot be completed. Why is the connection failing?

  • A. There is a problem with the IP routing.
  • B. The implicit deny at the end of the access list denies all the traffic.
  • C. The MDS cannot handle more than one Telnet session at once.
  • D. The management interface must be reset after the access list is applied.


Answer : B

Question 10

Refer to the below.
XPTO3# show interface fc1/7
Fc1/7 is down (Isolation due to domain overlap)
Hardware is Fibre Channel, WWN is
20:4e:00:05:30:00:63:9e
vsan is 10
Beacon is turned off
192 frames input, 3986 bytes, 0 discards
0 runts, 0 jabber, 0 too long, 0 too short
What must you do to resolve the connectivity problem over the fc1/7 interface?

  • A. The interface port type must be set to TE_port.
  • B. The VSAN load balancing scheme must be changed.
  • C. The Domain ID on the switch must be Changed.
  • D. The Beacon should be turned on.


Answer : C

Question 11

Refer to the exhibit.


Refer to the exhibit. The customer network has blue and red VSANs redundantly
connected, Path A having a 4-ISL port channel and Path B having a 2-ISL port channel.
Changes to the physical topology are not allowed for the next six months. All the traffic now
flows over Path A with congestion occurring on both VSANs at peak times. The blue VSAN
is, on the average, generating four times the amount of data than that of the red VSAN.
How can the blue and red VSAN traffic be separated over the two paths, while preserving
redundancy?

  • A. Make a zone in the blue VSAN with only ISL ports on Path B, and make another zone in the red VSAN with only ISL ports on Path A.
  • B. Make a zone in the blue VSAN with only ISL ports on Path A, and make another zone in the red VSAN with only ISL ports on Path B.
  • C. In the blue VSAN, give Path B a lower FSPF cost than Path A; in the red VSAN, give Path A a lower FSPF cost than Path B.
  • D. In the blue VSAN, give Path A a lower FSPF cost than Path B; in the red VSAN, give Path B a lower FSPF cost than Path A.


Answer : C

Question 12

What should be applied to the interface fc1/1 of the 48-port 8Gb/s module if the interface
will be used for the ISL connectivity and must provide 8Gb/s connectivity over a DWDM
optical network?

  • A. The interface must be configured as E_port or TE_port.
  • B. The interface must use special 8Gbps DWDM SFP.
  • C. QoS must be used to guarantee the ISL bandwidth.
  • D. The interface must be placed in shared mode to utilize all available bandwidth.


Answer : A

Question 13

Refer to the exhibit.


Which two options from the Tools menu would you select to verify connectivity and latency
to a Fibre Channel end device? (Choose two.)

  • A. Switch Health
  • B. Fabric Configuration
  • C. End to End Connectivity
  • D. Ping
  • E. Device Manager


Answer : C,D

Question 14

Which two features help you verify connectivity between host and storage devices?
(Choose two.)

  • A. fcanalyzer
  • B. Cisco Traffic Analyzer
  • C. EnD.to-End Connectivity Analysis
  • D. Zone Merge Analysis
  • E. fcping


Answer : C,E

Question 15

How many ports are addressable on a fabric arbitrated loop?

  • A. 126
  • B. B. 127
  • C. 255
  • D. 256


Answer : B

Page 1